Acetate, TFA and Net Peptide Content: Why Two 10 mg Vials Can Weigh Differently
Research use only. StarBio products are supplied strictly for in-vitro laboratory research by qualified professionals. They are not for human or veterinary use, not for diagnostic or therapeutic use, and have not been evaluated by the FDA. This page covers documentation, logistics and handling only. It is not usage guidance.
A vial labelled 10 mg and a certificate reading 99% purity do not, together, tell you that the vial holds 9.9 mg of peptide. Lyophilized peptide powder always contains other things that a purity test cannot see: counter-ions and water. How much of the powder is actually peptide has its own name, net peptide content, and it explains why two vials with the same label can hold different amounts. This page explains the chemistry and what to look for on a report.
Why a peptide is a salt
Most peptides carry basic groups: the amine at the N-terminus and the side chains of lysine, arginine and histidine. In the acidic conditions used to purify them, each of those groups picks up a proton and pairs with a negatively charged counter-ion. When the solution is freeze-dried, the counter-ions stay. The powder in the vial is a salt of the peptide, and the counter-ion is part of its weight.
Acetate and TFA
Peptides made by solid-phase synthesis are cleaved from the resin and purified by reverse-phase HPLC using trifluoroacetic acid, so the first form of any purified peptide is the trifluoroacetate (TFA) salt. Many suppliers then exchange TFA for acetate, which is the usual form for supplied material. Hydrochloride is a third option.
- Weight. A trifluoroacetate counter-ion weighs about 113 g/mol and an acetate about 59. The same peptide as a TFA salt therefore carries nearly twice the counter-ion weight.
- Assays. Residual trifluoroacetate has been reported to interfere with some cell-based assays, which is the usual reason laboratories ask for acetate.
- Detection. Neither counter-ion shows in the purity figure. Counter-ion content is measured separately, typically by ion chromatography.
The salt form is a fair question to put to any supplier, and a certificate may state it.
Water
Freeze-drying removes most of the water but not all of it, and many peptides take more back up from the air each time a vial is opened. Small, polar and basic peptides are the most hygroscopic. Residual water is typically measured by Karl Fischer titration. Like counter-ions, it adds weight that an HPLC purity test does not register.
A worked example
Take Selank, a heptapeptide of 751.89 g/mol with three basic groups: the N-terminal amine, a lysine and an arginine. This is arithmetic for illustration, not a measurement of any lot.
- If all three groups are paired with acetate, the counter-ions add 3 x 60.05 = 180.15 g/mol.
- The peptide is then 751.89 out of 932.04, or about 81% of the salt by weight.
- If the powder also holds 5% water, the peptide falls to about 77% of the powder.
So 10 mg of that powder would hold roughly 7.7 mg of peptide, while a purity test on the same powder could correctly read 99%. Both numbers are true. They answer different questions. In general, net peptide content often falls between 60 and 90 percent, lower for small basic peptides and higher for large or neutral ones.
Why two 10 mg vials can differ
A label can mean two things. It can state the weight of powder filled into the vial, or it can state the amount of peptide, with the fill adjusted for net peptide content. The two conventions give different amounts of peptide for the same label, and a label rarely says which was used.
This is where measured content on a laboratory report earns its place. Some laboratories quantify the peptide in the vial against a reference and report it in milligrams. StarBio’s Janoshik reports do: 10.21 mg found in the BPC-157 10 mg lot, 10.74 mg in TB-500, 10.13 mg in Selank and 9.48 mg in Cagrilintide. A measured content is the direct answer to how much peptide is in the vial, and it cannot be worked out from a purity percentage.
How net peptide content is measured
- Amino acid analysis. The peptide is hydrolysed and its amino acids quantified. The classic method.
- Elemental nitrogen. Total nitrogen is measured and compared with the amount the formula predicts.
- Quantitative HPLC or NMR against a reference standard of known content.
None of these is part of a routine purity report. If the exact mass of peptide matters to your work, it is a figure to ask for.
Four questions worth asking any supplier
- Which salt form is this lot: acetate, TFA or hydrochloride?
- Does the label state the weight of powder or the weight of peptide?
- Does the report give a measured content, or only purity?
- Is water content or counter-ion content reported anywhere?
Related: what 99% purity means, glossary: net peptide content, how to read a certificate of analysis, Selank research guide.
For laboratory research use only. Not for human or veterinary use.
New reports and guides, by email
A short note when a new laboratory report is published, when a compound returns to stock, and when a new guide goes up. Nothing else. Leave whenever you like.
For laboratory research use only. No dosing or protocol content is ever sent.

