How to Vet a Research Peptide Vendor in 10 Minutes
Research use only. StarBio products are supplied strictly for in-vitro laboratory research by qualified professionals. They are not for human or veterinary use, not for diagnostic or therapeutic use, and have not been evaluated by the FDA. This article covers documentation and supplier evaluation only. It is not usage guidance.
Most problems with research peptides are not discovered in the lab. They are discovered at the ordering stage, by people who did not ask the right questions before paying. The checklist below takes about ten minutes per supplier. It is vendor-neutral: apply it to StarBio as strictly as to anyone else.
1. Is there a certificate for this lot, or just for “the product”?
A Certificate of Analysis describes one batch of material tested on one date. A supplier who shows a single certificate for a product that has been on sale for two years is showing you a brochure. Look for a batch or report reference that changes over time, and for a way to find the certificate that matches the material you would receive. If the supplier publishes a library, check whether it lists one entry per compound or one entry per lot. Lot-level history is the stronger signal.
2. Who ran the test?
The laboratory named on the certificate should be independent of the supplier and of the manufacturer. In-house results are not worthless, but they cannot stand alone. Independent laboratories commonly used in this space publish a report reference you can check against their own records. If the certificate names no laboratory, or names one you cannot find, treat the document as unverified.
3. Does the report prove identity as well as purity?
These are two different measurements and both are needed.
- Purity is usually reported from HPLC as an area percentage: how much of what is in the vial is the main peak versus other peaks. A pure sample of the wrong molecule still scores well here.
- Identity is confirmed by mass spectrometry: the measured mass matches the theoretical mass of the stated sequence. Without this line, the certificate does not show that the material is what the label says.
Some suppliers publish HPLC-only reports. Ask why.
4. Does the certificate say how much is actually in the vial?
Purity and quantity are not the same thing. A certificate can show 99 percent purity on a vial that contains a quarter of the labelled mass. Look for a measured content figure (sometimes called net content, fill or quantification) next to the labelled amount. If it is missing, the supplier has not shown you how much material you are paying for.
5. Can you connect the vial to the paperwork?
Trace the chain yourself: label, lot or batch identifier, certificate, laboratory record. Every link should be checkable without the supplier’s help. Where a label does not carry a lot number, there should be a documented way to resolve an order to its batch. At StarBio that is the verify-lot form; the honest version of this article notes that printed lot numbers on labels would be better, and that is on our list.
6. Is the catalogue data consistent?
Open any product page and check for CAS number, molecular weight, formula and sequence. Then check them against a public reference such as PubChem. Suppliers who get the identity data wrong on the page are unlikely to be careful elsewhere. Also compare the sequence on the page with the mass reported on the certificate. They should agree.
7. What does the storage and handling information look like?
Lyophilised peptides are shipped and stored under specific conditions, and the supplier should state them plainly: temperature range for powder, protection from light, and what changes once a vial is in solution. Vague wording (“store in a cool place”) is a small thing that tends to travel with larger ones.
8. Are the claims research claims?
A research supplier describes compounds in terms of what the literature studies them for, cites that literature, and stops. Pages that describe results, benefits or protocols are describing something other than a research material. This matters for your own compliance as well as the supplier’s.
9. How does the supplier handle problems?
Before ordering, read the returns, shipping and damaged-order policies. Then send one question to support and time the reply. A supplier who answers a documentation question quickly and specifically before the sale is more likely to do so after it.
10. What does the community record show?
Independent test aggregators and community forums keep histories of vendor results, including failures. Read the failures, not just the passes, and look at dates: one good result is a data point, a consistent record over many lots is a process. If a supplier is absent from every independent record, that absence is information too.
A ten-minute score
Give one point for each question the supplier passes without you having to ask. Eight or more and the paperwork is doing its job. Five to seven, ask the missing questions and see how the supplier responds. Below five, keep looking. We publish StarBio’s own answers to each of these on the Quality Standards page and in the COA Library, and we would rather you check them than take our word.
For laboratory research use only. Not for human or veterinary use.
New reports and guides, by email
A short note when a new laboratory report is published, when a compound returns to stock, and when a new guide goes up. Nothing else. Leave whenever you like.
For laboratory research use only. No dosing or protocol content is ever sent.

